Study on downward flame spread over extruded polystyrene foam in a vertical channel: Influence of opening area

Experimental methods and theoretical analysis are employed to investigate effects of channel opening area on downward flame spread characteristics of extruded polystyrene (XPS) thermal insulation materials on building facade. The average flame height first drops and then rises as dimensionless opening area (the ratio of sidewall opening area to sidewall area, ie, S^*) increases. As S^* rises, both the average and maximum temperature of the curtain wall decrease, and the decreasing of the average temperature is linear. XPS surface temperature history can be divided into four stages, ie, inapparent rising stage (preheating), significant rising stage (melting), dropping stage (pyrolysis), and rerising stage (ignition). The preheating length first rises and then drops as S^* increases. The XPS flame spreads steadily at the early period while acceleration occurs at the later period. For different opening areas, the difference in spread distance history is not apparent in the early stage while this difference is significant in the later stage. The flame spread rate (V_f) first increases and then decreases as S^* rises. A downward flame spread model for XPS in vertical channel with openings is built. The varied trend of V_f predicted using this model corresponds to the experimental result.     

Impacts of spectral variations in multiwavelength excitation method on measurements of fluorescently whitened papers

The multiwavelength excitation (MWE) method for measuring the colorimetric properties of fluorescent whitening agent (FWA)‐treated specimens illuminated by a standard daylight illuminant computationally approximates not the spectral power distribution (SPD) of the illuminant but the luminescent SPD excited thereby by a weighted sum of the luminescent SPDs excited by a few different narrow‐band illuminations. The weights are optimized for the actual SPDs of those illuminations and the bispectral luminescent radiance factors of typical FWA‐treated paper specimens. Since the latter is invariant among instruments once provided as the common numerical data, the variations of the narrow‐band SPDs give major impacts to the reproducibility of this method. The weights optimized for the varied SPDs, however, mitigate the impacts. For investigating how they impact, one basic illumination system and its 16 simple variation systems were built virtually. The basic system consists of three narrow‐band LEDs and one blue‐excited white LED, whereas the individual simple variation system has either the peak wavelength or spectral width of one of the four LEDs (including the blue LED in the white LED) varied. With those systems, seven FWA‐treated papers with the known bispectral radiance factors were measured computationally by simulating the procedure of the MWE method. The differences in the colorimetric values measured with the simple variation systems from those with the basic system are far below the just noticeable difference, which indicates that the MWE method can be a practical solution for better reproducibility in measuring FWA‐treated papers.     

纸基底印刷无芯片RFID湿度传感器* .txt

摘要：提出了一种基于纸基底的喷墨印刷无芯片RFID湿度传感器，通过遗传算法与射频仿真软件HFSS相结合，对常规开口环谐振器结构进行分布式加载，得到目标频率为245 GHz的谐振特性良好的传感器模型；采用DMP3000型材料打印机，在不同纸基底上喷墨印刷银墨水制作传感器，以纸张本身的吸水性实现湿度传感；研究不同纸基底对湿度传感器感湿灵敏度和恢复度的影响。结果表明，柯达相纸传感器的灵敏度最高，高湿灵敏度可达到8 MHz%RH，双铜纸湿度传感器恢复度高且恢复时间短，仅为2 min；两种基底湿度传感器皆有较好的一致性、中长期稳定性，且湿敏特性在20℃～30℃范围内受温度影响较小。对纸基湿度传感器的感湿机理进行了分析，纸主要成分纤维素表面的羟基与吸附的水分子作用形成氢键，改变了基底的介电参数，传感器的湿敏特性与纸的成分和结构有关。 .txt     

A model of splats deposition state and wear resistance of WC-10Co4Cr coating

In this research both low temperature high velocity oxygen-fuel flame (LT-HVOF) and high velocity oxygen-fuel flame (HVOF) techniques were employed to prepare WC-10Co4Cr splats and coatings. In situ cutting of WC-10Co-4Cr splats was carried out with focused ion beam (FIB), and a model was proposed to describe how the wear resistance of WC-10Co4Cr coatings was correlated with its residual stress state and the splats deposition state. It was observed that in LT-HVOF spraying process, WC-10Co4Cr splats were slightly melted showing "hill" shape, while in HVOF spraying process, the splats were half melted having the appearance of "concavity". The residual stress of WC-10Co4Cr coatings is determined by the size, melting state, flight speed and temperature gradient of splats. In this paper, the quantitative function formula involving heating temperature and the flight speed of the powder is put forward for the first time to predict the wear resistance of the WC-10Co4Cr coatings. This will provide a theoretical basis for engineering practice and an effective way to save costs.     

辊式涂布法构建纸基牢固超疏水表面

采用辊式涂布的方法在纸基材料上构建超疏水表面，并对超疏水表面的牢固性、自清洁性和疏水性能进行评价。用γ-氨丙基三乙氧基硅烷和1H,1H,2H,2H-全氟辛基三乙氧基硅烷（POTS）对微米级和纳米级两种尺寸的TiO₂粒子进行疏水改性处理，然后将改性后的微/纳米TiO₂涂布在纸基材料表面。采用红外光谱（FTIR）对改性后的微/纳米TiO₂的化学组成进行了分析，采用扫描电镜（SEM）对涂布纸表面结构进行了表征，通过接触角、耐磨性和自洁净测试评价了涂层表面的超疏水性、牢固性和自清洁性。改性TiO₂的FTIR分析显示在1000～1500cm^-1之间出现多个C—F键的伸缩振动峰，表明POTS通过化学键与TiO₂表面发生了结合。涂布纸表面的SEM分析可以看出，纸基材料表面上均匀分布了微米和纳米尺寸的TiO₂颗粒，具备了类似荷叶表面微-纳结构的粗糙表面。涂层表面的水接触角为153°±1.5°，滚动角为3.5°±0.5°，水滴在涂层表面呈球形，极易滑落，涂层在水中浸泡7天后，接触角没有发生明显变化，表明纸张表面具备了优异的超疏水性能，且疏水稳定性较好。涂层表面经过10次循环磨损试验后，接触角仍能达到150°，滚动角为9°，表明机械摩擦没有对涂布纸表面的化学成分和粗糙结构造成明显的破坏，超疏水表面的牢固性较好。自洁净测试表明，涂布纸表面具有良好的自清洁和防污性能。该工艺过程操作简单，易于实现工业化生产，为在纸基表面构建综合性能优异的超疏水表面提供了一种新的便利途径。     

二甲醚球形扩散火焰的熄火机理研究

采用改进的PREMIX模型及"化学爆炸模式分析(CEMA)"方法,对二甲醚(DME)球形扩散火焰的熄火机理进行数值诊断,分析环境氧气摩尔分数(X_(O_2))及详细基元反应对熄火极限的影响,利用"爆炸因子"和"分岔因子"的概念,确定控制DME球形扩散火焰熄火的关键反应动力学因素。结果表明:DME冷焰具有比热焰更宽的可燃范围;冷焰对X_(O_2)的敏感性弱很多,热焰中具有正特征值的CEM首次出现在最高温度处;在熄火极限附近,CEM的特征值变为虚数,说明熄火伴随着振荡;热焰的熄火主要由小分子所参与的高温反应所控制,而冷焰熄火主要由大分子所参与的低温反应所控制。     

Chemical exposures from upholstered furniture with various flame retardant technologies

Upholstered furniture is often manufactured with polyurethane foam (PUF) containing flame retardants (FRs) to prevent the risk of a fire and/or to meet flammability regulations, however, exposure to certain FRs and other chemicals have been linked to adverse health effects. This study developed a new methodology for evaluating volatile organic compound (VOC) and FR exposures to users of upholstered furniture by simulating use of a chair in a controlled exposure chamber and assessing the health significance of measured chemical exposure. Chairs with different fire-resistant technologies were evaluated for VOC and FR exposures via inhalation, ingestion, and dermal contact exposure routes. Data show that VOC exposure levels are lower than threshold levels defined by the US and global indoor air criteria. Brominated FRs were not detected from the studied chairs. The organophosphate FRs added to PUF were released into the surrounding air (0.4 ng/m³) and as dust (16 ng/m²). Exposure modeling showed that adults are exposed to FRs released from upholstered furniture mostly by dermal contact and children are exposed via dermal and ingestion exposure. Children are most susceptible to FR exposure/dose (2 times higher average daily dose than adults) due to their frequent hand to mouth contact.     

Different chemical effect of hydrogen addition on soot formation in laminar coflow methane and ethylene diffusion flames

Previous studies showed that adding hydrogen (H₂) can have an opposite chemical effect on soot formation: its chemical effect enhances and suppresses soot formation in methane (CH₄) and ethylene (C₂H₄) diffusion flames, respectively. Such opposite chemical effect of H₂ (CE-H₂) remains unresolved. The different CE-H₂ is studied numerically in the two laminar coflow diffusion flames. A detailed chemical mechanism with the addition of a chemically inert virtual species FH₂ is used to model the gas-phase combustion chemistry in this study. Particularly, a reaction pathway analysis was performed based on the numerical results to gain insights into how H₂ addition to fuel affects the pathways leading to the formation of benzene (A₁) in CH₄ and C₂H₄ flames. The numerical results show that the CE-H₂ in CH₄ diffusion flame to prompt soot formation is ascribed that the higher mole fraction of H atom promotes the formation of A₁ and Acetylene (C₂H₂) and leads to higher nucleation rate and eventually higher soot surface growth rate. In contrast, adding H₂ to C₂H₄ diffusion flames decreases soot nucleation and surface growth rate. The lower soot nucleation rate is due to the lower mole fractions of pyrene (A₄), while the lower soot surface growth rate is due to the lower mole fractions of H atom and C₂H₂, higher mole fraction of H₂ and lower soot nucleation rate. Furthermore, the CE-H₂ in C₂H₄ diffusion flames promotes the formation of A₁, but suppresses the formation of A₄.     

铝金属化纸制备工艺的专利技术发展

通过对铝金属化纸领域专利技术的收集、分析、标引,介绍了铝金属化纸的制备方法及种类,包括铝粉涂布、铝箔纸以及可降解回收的真空镀铝纸等;并对其专利申请量、区域分布以及渡铝技术进行了分析,同时对各技术的发展历程和改进情况进行了梳理归纳。     

High‐performance printable paper‐like composites derived from plastic flexible film wastes

Owing to lack of proper recycling methods, plastic flexible film wastes are usually directly discarded or incinerated, which brings about severe environmental pollution. Therefore, converting plastic wastes into value‐added products has received more and more attention in recent years. In this work, paper‐like composites derived from plastic flexible film wastes were prepared via the thermally induced phase separation method by adding polyethylene‐graft‐maleic anhydride (PE‐g‐MAH) as a compatibilizer and fumed silica as an additive. The resulting paper‐like composites were characterized by SEM and infrared spectroscopy. Other properties such as mechanical properties, thermal properties, whiteness, printability and adsorption performance were also tested in detail. It was found that remarkable enhancements in mechanical, thermal and printable properties of the paper‐like composites were obtained when nano‐SiO₂ loading was 2.5–3 wt%. Uniformly distributed holes that can endow good printability by providing space for ink or other functional molecules were observed by using SEM. Furthermore, the CIE whiteness value of the resulting composites can reach 91.6%–96.7% on adding nano‐SiO₂. Additionally, the paper‐like composites integrating nano‐SiO₂ and PE‐g‐MAH exhibited good solid ink affinity and high water or oil adsorption capacity. Thus, according to this research, high‐performance printable paper‐like composites used as major components of multifunctional papers can be prepared based on plastic flexible film wastes. © 2019 Society of Chemical Industry